INDUSTRIAL CONTROLLERS AND I/O MODULES
PD600 and PD800 Series
COPP ENABLED MODULES
COPP enabled modules are process controllers, I/O-modules and sensors, which are programmable in COPP by means of the tools in the VIGO6 Integrated Development Environment.
Additional info about COPP enabled modules, including features and design, building clusters, network types, wiring, dimensions, etc. can be found on this page:
Introduction to COPP enabled modules
PD688
7" Colour Graphics Display with capacitive touchscreen, Dual 100 Mbit Ethernet, 2 individual P-NET via RS485, 2 digital I/O’s •...
PD802 COPP DPI
Distributed Process Intelligence type, P-NET via Light-Link, RS-485, USB Interface, Dual 100 Mbit Ethernet • Process Automation Controller • Programmable...
PD803 COPP DPI GSM GPS
Distributed Process Intelligence type, P-NET via Light-Link, RS-485, Dual 100 Mbit Ethernet, USB Interface, GSM, GPS. • Process Automation...
PD804 COPP DPI 4G & GPS
Distributed Process Intelligence type, P-NET via Light-Link, RS-485, Dual 100 Mbit Ethernet, USB Interface, 4G LTE, GPS. • Process...
PD820 15 CH. DIGITAL I/O
15 ch. Digital I/O, Push-pull output, Built-in input and output functions, P-NET via Light-Link, Programmable in COPP • Digital Source or Sink...
PD821 15 CH. DIGITAL IN
15 ch. Digital in, Digital inputs for nominal 24 volt signals, P-NET via Light-Link, Programmable in COPP • Digital inputs for nominal...
PD840 15 CH. ANALOGUE IN
15 ch. Analogue in, Analogue inputs for 4-20 mA signals, P-NET via Light-Link, Programmable in COPP • Analogue inputs for 4-20 mA...
PD850 MULTIFUNCTION I/O
Multifunction I/O, Digital Source I/Os for nominal 24 volt, Analogue I/Os for 4-20 mA signals, P-NET via Light-Link, Programmable in COPP • Digital...
PD870 MOTOR CONTROLLER
Be aware that the Motor Controller is a combination of the PD870 COPP controller and the BM102 high power base...
PD610
Communication Module, COPP Gateway, P-NET, RS-485, CAN bus interface, Ethernet, P-NET via Light-Link • P-NET-RS485 or CAN bus interface •...
PD630
• Ratiometric bridge sensor input with sensor supply • Six wire connection with shield for sensors • Fits both low...
PD644 Analogue I/O – HART
Analogue I/O module, 4 analogue input 4-20 mA, HART and 2 analogue channels 4-20 mA I/O, P-NET via Light-Link •...
PD645
• Analogue input/output for 0-10 V signals • Programmable in COPP • P-NET via Light-Link • Overload/underload protection and alarming...
PD3221B
• 4 Digital Source, Sink or push-pull I/O´s • Load current measurement • 2 Digital Inputs • 1 Analog Current...
PD940 DIPSTICK
Level, conductivity and temperature transmitter, Analogue current output: 4-20 mA, Digital I/O, P-NET via RS485 • Compact sanitary design - designed...
PD947
GPS Navigation Receiver, Designed for rugged operating conditions, waterproof to IP67, P-NET via RS485 or Ethernet • High sensitivity GPS receiver for...
PD3122
• 16 Digital Source, Sink or Push-Pull I/O´s • Load current measurement • P-NET via RS485 cable • Built-in input...
NON-COPP ENABLED MODULES
NON-COPP enabled modules are process controllers and I/O-modules which do not offer support for programming in COPP. However, they they can be fully integrated in projects with modules supporting COPP. Some of these modules may be programmed using the Process-Pascal programming language.
Additional info about NON-COPP enabled modules can be found on this page: Introduction to NON-COPP enabled modules
PD528
Tank Gauging Module, 5-ch.: Pressure, Analogue output 0/4-20 mA, Digital I/Os, Tank Gauging. • Sensor type: Differential Pressure •...
PD600B
Distributed Process Intelligence type, P-NET via Light Link and RS-485 Interface. • Real time clock with battery backup. • 64 ...
PD601
Distributed Process Intelligence type, PD 601, P-NET via Light Link, RS-232 Interface • Real time clock with battery backup. •...
PD602B
Distributed Process Intelligence, P-NET via Light-Link and 10/100 Mbit/s Ethernet LAN Interface. • Real time clock with battery backup. •...
PD620
• Individually Configurable Digital I/Os for nominal 24 volts signals and 1 amp (2 Amp) loads. • Built in input...
PD621
• Individually Configurable Digital I/Os for nominal 24 volts signals and 1 amp (2 Amp) loads. • Built in input...
PD622
• 6 Individually Configurable digital Inputs for nominal 24 volts signals. • Built in input functions. • Autonomous counting to...
PD640
Analogue Interface Module, 4 analogue channels, configurable for either 0-20 mA or 4-20 mA signal types, • Analogue current I/O module...
PD641
Analogue Interface Module, 3-ch. input each of which can be configured for either Pt100 or Pt1000 sensor types • Temperature input...
PD642
Analogue Interface Module, 4-ch. individual inputs (voltage 0-100 mV or thermocouple temperature sensor), P-NET via Light-Link • 0-100 mV or thermocouple...
PD643
Analogue Interface Modul, 3-ch. voltage/temperature (0-100 mV/Pt100/thermocouple) • Temperature inputs Pt100 / pt1000 / thermocouple and 0-100 mV • 0-100 mv /...
PD661
Simple P-NET Interface, RS-485 to Light-Link converter. • Its main purpose is to provide a transparent link between standard RS485...
PD662
Redundancy P-NET Interface, RS-485 to Light-Link converter. • Provides a redundant and transparent link between optical Light-Link and a duplicated...
PD663
Simple P-NET Interface Triple Speed, RS-485 to Light-Link converter • Provides a transparent link between standard RS485 P-NET and the...
PD667
Profibus DP-V0 Essential Features Master • RS485 interface for Profibus • Light-Link interface for P-NET • Advanced internal self testing • Wide...
PD681
• Sealed Construction • 28 Key Membrane click-switch Keyboard • Backlit Graphics LCD Display • User definable overlay • Two...
PD690
• Power supply input transient voltage protection • Wrong polarity protection • Output short-circuit protection • LED On / Error...
PD951 RFID reader
PD 951 RFID Reader, general purpose LF Dual Band RFID reader. • High performance Dual band RFID Reader 125 kHz...
PD3950
PD 3950 PC P-NET interface, USB interface • P-NET Fieldbus communication interface. • P-NET RS485, multi-master P-NET interface. • Galvanically...
PD990
PD 990 4-WIRE P-NET Conditioner • Termination of a 4-WIRE P-NET bus. • Connection of a traditional P-NET module to...
PD981 KeyLED (OEM)
P‑NET slave module, A custom designed front panel mounted keyboard, Operator input and LED module for other P-NET devices.
P-NET LAN to P-NET RS485 interface
P-NET LAN to P-NET RS485 interface unit including: 1 pcs. PD 602S, mounted on BM 016 1 pcs. PD 661...
Unit for galvanic isolation of P-NET RS485
Unit for galvanic isolation of P-NET RS485 including: 2 pcs. PD 661 SPI, mounted on BM 010 1 pcs. bottom...
BASE MODULES
Products in this category are Base Modules for both the M36- and the M100 Series.
ACCESSORIES
Products in this category are accessories for use with the products above.
Power Rails
- Power Rail, 1 pcs. length 115 mm (fit for 3 base modules in the M36 product range or 1...
M36 Accessories
- Fibre optics kit consisting of: 5 m of plastic optical fibre 2 x 20 holding wedges for left and...
GPS and GSM antenna cable kit for PD803/PD804
GPS antenna and cable kit for PD 803 and 804. Cable length 10 m
Antenna collection for PD664
GSM Aerial Screw nut cover for GSM aerial Antenna cable, FME/SMB 0,6 meter
Loop antenna for PD951 RFID Reader
Loop antenna for PD951 RFID Reader Ø175mm: This antenna is designed to be used with the PD 951 RFID Reader...
SPAREPARTS
Modules listed in this category are process controllers and I/O-modules, and accessories, which can be delivered as spareparts for existing control systems (not recommended for use in new projects).
PD664
P-NET GPRS Interface, built-in triple-band mobile phone, Light-Link/RS485 P-NET interface, P-NET communication via GPRS • Encrypted GPRS communication • Configuration...
PD3120 Digital I/O interface 16 ch
This module must only be used to replace defective modules in an existing installation. The module is an intelligent...
PD3221 Universal Process Interface, UPI
The module contains 6 digital input channels, (4 of which can be configured as digital outputs) 2 analog input channels...
PD3230 Weight transmitter
The module contains one high resolution Weight input channel with a parallelling capacity of up to 10 x 600 or...
PD3235 Weight transmitter for 10 load cells
The module contains one high resolution Weight input channel with a parallelling capacity of up to 10 x 300 Ohm...
PD3240 Analog Interface Module AIM
This module must only be used to replace defective modules in an existing installation. For new installations, please use PD...
PD3250 Analog Interface Module, AIM, voltage measurement
This module must only be used to replace defective modules in an existing installation. For new installations, please use PD...
PD3940 P-NET to RS232 converter
Communication module with P-NET interface and RS232 port. Used for communication with printers, barcode readers and other equipment without P-NET...
PD5000-series
FEATURES • 32 Bit Microprocessor (68020) • Multi-Tasking Capabilities • Programmed in Process-Pascal • Large Expandable Data Memory • Two...
PD626 – Stepper motor controller and driver
The PD 626 is an integrated controller and driver for stepper motors. It can directly drive a unipolar stepper motor....
Gasket for PD4000 Display and PD681 Display
Gasket for PD4000 Display and PD681 Display (spare part)
DISCONTINUED PRODUCTS
Products in this category have effectively been removed from production. It is still possible to find relevant information regarding the products by navigating to the individual products information page like earlier. On this page, you’ll also be presented with relevant replacements for the discontinued counterpart.
PD600
This product have been replaced by PD600B. Distributed Process Intelligence type, PD 600, P-NET via Light-Link, RS-485 Interface •...
PD602
This product have been replaced by PD602B. Distributed Process Intelligence type, PD 602, P-NET via Light-Link, Ethernet LAN Interface...
PD1610 Analog Transmitter
The PD1610 analog transmitter is part of PROCES-DATA's module series 1000. The PD1610 module has been developed for storing...
PD1651 Multifunction Transmitter
The PD1651 Multifunction transmitter is a module in PROCES-DATA's module series 1000. The PD1651 module is intended for the...
PD1431 Weight Transmitter
The PD1431 Weight transmitter is a module in PROCES-DATA's module series 1000. The PD1431 module is intended for the...
PD1611 Analog Transmitter
The PD1611 Analog Transmitter is part of PROCES-DATA's module series 1000. The PD1611 module has been developed for storing...
PD1652 Multifunction Transmitter
The PD1652 Multifunction Transmitter is a module in PROCES-DATA's module series 1000. The PD1652 module is intended for the collection...
PD4500 Hand-Held Terminal
The PD4500 is a hand-held controller designed for mobile data collection, e.g. to collect service information when walking around a...
