SMS Channel

Registers in SMS channel:

RegNo	Identifier	Memory type	Read Out	Type
0	SMSOutputBuffer	RAM Read Write	-------	Buffer
1	SMSInputBuffer	RAM Read Write	-------	Buffer
2	SMSOutputStatus	RAM Read Write	-------	Record
3	SMSFlagReg	EEPROM RPW	Binary	Bit8
4
5	WatchdogSMSConfiguration	EEPROM RPW	-------	Record
6
7	Statistics	RAM Read Write	-------	Record
8
9
10
11
12
13
14	Guid	PROM Read only	-------	String
15	ChError	RAM Read Write	-------	Record

RegNo 0: SMSOutputBuffer

SMSType = RECORD
	PhoneNo:	String[40];
	Message:	String[160];
End;

SMSOutputBuffer: Buffer[1] of SMSType;

When an SMS is written to SMSOutputBuffer, the message is sent to the requested phone number. After transmission, or if transmission fails, the SMS is deleted from SMSOutputBuffer. Note: Since this register is stored in volatile RAM, it will be cleared after power off and reset.

RegNo 1: SMSInputBuffer

SMSType = RECORD
	TypeID	Byte;
	TimeDate	TimeDateType;
	PhoneNo:	String[40];
	Message:	String[160];
End;

SMSInputBuffer: Buffer[1] of SMSType;

TypeID

Holds the type of SMS received:

0:	Normal Text SMS
1:	StatusReport

TimeDate

Holds the timestamp of the SMS.

Message

If a status report is received, the message will hold two numbers separated by a comma.

The first number is the message reference number. The second number is the message status code.

When an SMS is received, it is stored in the SMSInputBuffer. Note: Since this register is stored in volatile RAM, it will be cleared after power off and reset.

RegNo 2: SMSOutputStatus

SMSType = RECORD
	MessageReferenceNo:	Integer;
	StatusIDNo:	Integer;
End;

MessageReferenceNo

When an SMS is sent, the service centre returns a reference number. This number can be compared with a status report. MessageReferenceNo is set to -1 when a message is written to the SMSOutputBuffer. Note: Since this register is stored in volatile RAM, it will also be set to –1 after power off and reset.

StatusIDNo

If sending an SMS fails, bit 9 in ChError is set and the StatusIDNo is loaded with a number representing an SMS error described in this table:

StatusIDNo	Description
28	Unidentified subscriber
42	Congestion (Service centre is blocked)
192	Service centre busy
305	Invalid Phone number
500	Non specific error

For all specified errors, attempts should be made to send the SMS at a later time.

StatusIDNo is set to -1, when a message is written to the SMSOutputBuffer. When MessageReferenceNo changes from -1 and StatusIDNo remains at -1, the SMS has been sent without any problems. Note: Since this register is stored in volatile RAM, it will also be set to –1 after power off and reset.

RegNo. 3: SMSFlagReg

FlagReg:

Bit8;

FlagReg :

0: Enable SMS Status reports

1: Not used

2: Not used

3: Not used

4: Not used

5: Not used

6: Not used

7: SMSOnly

The FlagReg can be accessed as one Byte or as individual bits.

Bit 0: Enable SMS Status reports

The Enable SMS Status reports flag configures the module to request SMS status reports from the service centre. The status reports are transported to the SMS input buffer.

Bit 7: SMSOnly

Important: Setting this flag disables GPRS in the module!

In the event that this flag is set the Red Error LED in the module will not be flashing as normal if the GPRS configuration is not valid. If the module has an open connection this will be terminated and the module will not make any attempts to connect, as long as SMSOnly is enabled.

RegNo 5: WatchdogSMSConfiguration

Record
	WDEnable	Boolean;
	PhoneNo:	String[40];
	WDText:	String[50];
End;

WDEnable

If set, this Boolean will enable the Watchdog functionality.

PhoneNo

This field holds the phone number to which an SMS is sent if the WDTimer (in the Service channel) reaches zero before it is preset again, i.e. no communication from a master. If no phone number is entered, no SMS is sent.

WDText

This string specifies the WatchdogSMS text.

RegNo 7: Statistics

Record
	ReceivedSMS:	LongInteger;
	SentSMS:	LongInteger;
End;

ReceivedSMS

This field holds the number of SMS messages received since the PD 664 was powered up, or since the counter was last reset.

SentSMS

This field holds the number of SMS messages sent since the PD 664 was powered up, or since the counter was last reset.

RegNo 14: GUID

GUID:

String[22];

Each channel type is identified by means of a unique GUID. The value of GUID for the SMS channel is: PD/551297-01.

RegNo 15: ChError

Record
	His:	Bit16;
	Act:	Bit16;
End;

There are two sets of error bits, actual and historical. The actual error bits reflect the current situation and will automatically follow any change.

The historical error bits reflect the history and have the purpose of holding sporadic errors. The historical error bits are set together with the corresponding actual bits. They remain set after a read, so each individual bit must be cleared manually, via P-NET. Only the bits where the corresponding actual bit is false can be cleared.

The “His data error” bit in the P-NET response is set if any historical bit is true.

The “Act data error” bit in the P-NET response reflects the validity of the data in the response. An error in registers involved in calculating the result gives “Act data error”.

See summary for how ChError.His can be cleared in particular M36 slave modules.

15	7	0

			0: Program_storage_fault

			1: RAM_storage_fault